Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Hirota, Noriaki; Nakano, Hiroko; Fujita, Yoshitaka; Takeuchi, Tomoaki; Tsuchiya, Kunihiko; Demura, Masahiko*; Kobayashi, Yoshinao*
The IV International Scientific Forum "Nuclear Science and Technologies"; AIP Conference Proceedings 3020, p.030007_1 - 030007_6, 2024/01
Dynamic strain aging (DSA) and intergranular stress corrosion cracking (intragranular SCC) occur in high temperature pressurized water simulating a boiling water reactor environment due to changes in dissolved oxygen (DO) content, respectively. In order to clearly understand the difference between these phenomena, the mechanism of their occurrence was summarized. As a result, it was found that DSA due to intragranular cracking occurred in SUS304 stainless steel at low DO 
1 ppb, while DSA was suppressed at DO 100 to 8500 ppb due to the formation of oxide films on the surface. On the other hand, when DO was increased to 20000 ppb, the film was peeled from the matrix, O element diffused to the grain boundary of the matrix, resulting in intergranular SCC. These results are indicated that the optimum DO concentration must be adjusted to suppress crack initiation due to DSA and intergranular SCC.
Yamamoto, Masahiro; Irisawa, Eriko; Igarashi, Takahiro; Komatsu, Atsushi; Kato, Chiaki; Ueno, Fumiyoshi
Proceedings of Annual Congress of the European Federation of Corrosion (EUROCORR 2019) (Internet), 5 Pages, 2019/09
Intergranular corrosion phenomena were analysed using modified reprocessing solution. The data indicated that corrosion rates increased with time at the initial stage, and these stayed at constant value. Intergranular corrosion propagated at grain boundary in the initial stage and then attacked whole grain boundary causing drop out of grains. Corrosion rates of steady state were sum of intergranular corrosion amounts and weight losses of dropped grains. Surface appearances and cross sections of corroded samples were analyzed. The results indicated that the initial stage of intergranular corrosion was characterized by the ratio of corrosion rates between grain boundary and matrix. These ratios differed from individual grain boundaries. Total corrosion rates were affected by the distribution of these ratios. These data were based on the numerical modelling of intergranular corrosion using cellular automata. And also, calculated results were compared with these analytical data.
The Working Team for Examination Operation of Samples From Core Shroud at Fukushima Dai-ni Unit-3
JAERI-Tech 2004-044, 92 Pages, 2004/05
JAERI-Tech-2004-044.pdf:15.18MB
The present examination has been performed with the objective to ensure the transparency of the examination as the third-party organization by providing technical basis for identifying the causes of cracking through examination of the sample taken from the cracked region of outer H6a welding portion of the core shroud at Fukushima Dai-ni Nuclear Power Station Unit-3, which was a part of sample stored in the Nippon Nuclear Fuel Development Co., Ltd. in the examination of Tokyo Electric Power Company in 2001. The present examination of the sample was conducted at the post irradiation examination facilities of JAERI. The following findings were obtained from the result of the present examination. (1)Three cracks were observed at the portion 3 to 9mm apart from the weld metal and the maximum depth was about 8mm. (2)Intergranular cracking was observed in almost whole fracture surface. The transgranular cracking was partially observed within the depth of about 300
m from the surface. (3)Hardening layer over Hv400 at its maximum was found from the surface to the depth of about 500m. Based on the examination results concerning presence of tensile residual stress by welding and relatively high dissolved oxygen contents in core coolant, it is concluded that the cracks were mainly initiated in the hardening layer by transgranular stress corrosion cracking and propagated along the grain boundaries.
Hamada, Shozo; Fukaya, Kiyoshi*; Kato, Chiaki; Yanagihara, Takao; Doi, Masamitsu*; Kiuchi, Kiyoshi
JAERI-Tech 2001-063, 49 Pages, 2001/10
JAERI-Tech-2001-063.pdf:13.39MB
The demonstration test for the acid recovery evaporator and the dissolver used in the major equipment of Rokkasho Reprocessing Plant (RRP), has been carried out. The mock-up miniature equipment has been employed to it. This test had been performed from April in 1998. The total time of demonstration test using the mock-up equipment is about two and half years, which corresponds to about 20,000 hours. After that, four of the seven heat transfer tubes used in the evaporator were drawn out and the corrosion level and the mechanical properties were evaluated for one of them. As a result, intergranular corrosion was recognized in the inner surface of the heat transfer tube and the corrosion depth at the grain boundary was statistically shown to be about one grain from the inner surface. Further, no change in mechanical properties was observed and growth of intergranular cracks in the inner surface of the specimen was found after flattering test.
Nishiyama, Yutaka; Fukaya, Kiyoshi; Suzuki, Masahide; Eto, Motokuni; *
Small Specimen Test Techniques; ASTM STP 1204, p.16 - 26, 1993/00
no abstracts in English
; Kondo, Tatsuo
Boshoku Gijutsu, 32(9), p.503 - 511, 1983/00
no abstracts in English
; Kondo, Tatsuo
Boshoku Gijutsu, 32(10), p.572 - 579, 1983/00
no abstracts in English
Yamashita, Shinichiro; Sekio, Yoshihiro; Sakaguchi, Norihito*; Shibayama, Tamaki*; Watanabe, Seiichi*; Kokawa, Hiroyuki*
no journal, ,
